Niche Zero
- 研磨范围
- 最粗约 1161 µm
- 每格变化
- ≈20 µm
- 调节方式
- 无级调节
- 冲煮方式
- 19
在最粗端约可达到 1161 µm，因此炉用滤泡壶、法压壶、冷萃部分超出其范围。
左右滑动可查看完整刻度
关于 Niche Zero
Niche Zero 是一款电动磨豆机，配备 63 毫米锥刀，无级调节。在最粗端约可达到 1161 µm，因此炉用滤泡壶、法压壶、冷萃部分超出其范围。每格大约改变 20 µm 的研磨度。
我们在这台磨豆机上发现了什么
核对依据
Niche's "The ultimate grind size guide for Niche grinders". 查阅于 2026 年 09 月 07 日。
This page used to carry numbers filed under Niche's own name, as though they came out of the box with the grinder. They did not. The instruction leaflet Niche ships carries no per-method table at all — it says only that the grinder is "factory calibrated and adjusted to setting 20".
Niche does publish a table, on its own site, and checking against it was not close. Four of the five methods Niche names were wrong here, and three had no overlap with the maker's band whatsoever: we had AeroPress at 12-18 where Niche says 30-35, V60 at 18-22 against 35-45, moka at 14-18 against 20-30. Anyone following this page was grinding up to 2.3 times finer than Niche recommends.
The five methods Niche names are now Niche's own figures. Drip, chemex and cold brew were dropped rather than kept under a maker's name the maker never gave them — they are interpolated between the five, which is both honest and, for the first time on this grinder, anchored to something published. The old cold-brew row also ran to 55 on a dial that stops at 50, so it was printing a setting the machine cannot be set to.
The table's numbers were read out of the page's own HTML rather than off a rendering of it. The neighbouring Niche Duo column holds different numbers in every row, and one mis-read cell has already cost this catalogue a whole grinder's curve.
尚未解决
French press is published as "45+" and is recorded here as 45-50, because 50 is where the dial ends. That is what the maker means and all the maker gives.
Niche Zero 覆盖的冲煮方式
这 19 项设定中有 5 项来自 Niche 官方公布的数据，其余由本机的研磨范围推算。 从这里开始，再按口味微调。
- 意式浓缩 刻度 5–20 · 约 200–300 µm 细 来自厂商
- 摩卡壶 刻度 20–30 · 约 300–400 µm 细 来自厂商
- 手冲 V60 刻度 35–45 · 约 450–650 µm 中细 来自厂商
- Chemex 刻度 40–44 · 约 700–900 µm 中粗
- AeroPress 刻度 30–35 · 约 400–700 µm 中细 来自厂商
- 法压壶 刻度 45–50 · 约 900–1200 µm 粗 来自厂商
- 冷萃 刻度 46–50 · 约 1000–1400 µm 特粗
- 滴滤/批量 刻度 37–42 · 约 600–800 µm 中等
- 虹吸壶 刻度 33–40 · 约 500–700 µm 中等
- Cold Drip 刻度 40–44 · 约 700–900 µm 中粗
- 炉用滤泡壶 刻度 45–50 · 约 900–1200 µm 粗
- 那不勒斯翻转壶 刻度 33–40 · 约 500–700 µm 中等
- 南印度滤器 刻度 35–45 · 约 450–650 µm 中细
- 杰贝纳陶壶 刻度 33–40 · 约 500–700 µm 中等
- Chorreador 刻度 35–45 · 约 450–650 µm 中细
- Dallah 刻度 6–28 · 约 200–400 µm 细
- Cafe de Olla 刻度 42–46 · 约 800–1000 µm 中粗
- Prestina 刻度 33–40 · 约 500–700 µm 中等
- 越南 Phin 刻度 42–46 · 约 800–1000 µm 中粗
Niche Zero — 常见问题
Niche Zero 是手摇磨豆机还是电动磨豆机？
Niche Zero 是一款电动磨豆机，配备 63 毫米锥刀。
Niche Zero 能磨出的研磨度范围是多少？
Niche Zero 最粗可磨到约 1161 µm，覆盖我们收录的 19 种冲煮方式。厂商没有公布最细刻度，因此我们不做标注。
能把其他磨豆机的研磨设置直接套用到 Niche Zero 上吗？
不能直接套用 — 每台磨豆机的刻度都是各自独立设定的，一台机型上有效的数字不会对应到 Niche Zero。请改用上方对照表按微米范围匹配。